James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.
TECHNICAL BULLETIN #17 – James Hardie Pros
Error message | View complete answer on https://www.jameshardie.com
Can you put a nail in Hardie board?
For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency. At the bottom, the siding should be face nailed, and at the top, it should be blind nailed.
Error message | View complete answer on https://legacyusa.com
Can you hammer a nail through Hardie board?
Yes you can. We recommend using 1 1/4″ smooth shank nails that are designed for use with Hardie Siding and Hardie Plank Siding.
Error message | View complete answer on https://www.quora.com
Can I use nails on fiber cement board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Error message | View complete answer on https://www.familyhandyman.com
What is the best way to fasten Hardie board?
James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together. Longer finish nails may bend.
Error message | View complete answer on https://www.jameshardiepros.com
Can you nail through Hardie board?
You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom. It’s best to use siding nails for face nailing or roofing nails for blind nailing.
Error message | View complete answer on https://legacyusa.com
Can you hang things on Hardie board?
Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).
Error message | View complete answer on https://www.jameshardie.com
Can you hammer a nail through Hardie board?
Yes you can. We recommend using 1 1/4″ smooth shank nails that are designed for use with Hardie Siding and Hardie Plank Siding.
Error message | View complete answer on https://www.quora.com
Can I use nails on fiber cement board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Error message | View complete answer on https://www.familyhandyman.com
Can you nail fibre cement board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Error message | View complete answer on https://www.familyhandyman.com
What type of nails are used for fiber cement siding?
Galvanized or stainless steel 6D and 8D nails are typically considered the best nails for fiber cement siding because they are the appropriate size and offer reliable durability.
Error message | View complete answer on https://allurausa.com
Can you hang things on cement board?
Pointers When Hanging Things to Hardie Board Use screws or nails explicitly designed for attaching to Hardie boards. Regular nails and screws will not penetrate the surface properly and can cause damage. Be careful not to overdrive the nails – Ensure you drive the pins firmly and don’t overdo it.
Error message | View complete answer on https://gsexteriorexperts.com
Can you hammer a nail into Hardie board?
Use screws or nails explicitly designed for attaching to Hardie boards. Regular nails and screws will not penetrate the surface properly and can cause damage.
Error message | View complete answer on https://gsexteriorexperts.com
Can you nail into cement board?
If you’re using galvanized nails, a general 1 ½‑inch galvanized nail should hold the concrete board firmly in place. Make sure the screw head is slightly indented into the cement board. You ideally want it flush with the surface. Too deep will weaken the hold and too high can interfere with thin tile installations.
Error message | View complete answer on https://www.fastenmaster.com
Can I use nails on fiber cement board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Error message | View complete answer on https://www.familyhandyman.com
What kind of nail to use on Hardie board?
TIP: Stainless steel fasteners are recommended when installing James Hardie products. Corrosion-resistant siding nails 11/4 in. long should be used to apply individual HardieShingles® to minimum 7/16 in.
Error message | View complete answer on https://www.jameshardiepros.com
What are the best fasteners for Hardie board?
Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
Error message | View complete answer on https://www.jameshardiepros.com
Is it better to nail or screw Hardie board?
James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above.
Error message | View complete answer on https://www.jameshardie.com
What are the best nails to use with Hardie board?
TIP: Stainless steel fasteners are recommended when installing James Hardie products. Corrosion-resistant siding nails 11/4 in. long should be used to apply individual HardieShingles® to minimum 7/16 in.
Error message | View complete answer on https://www.jameshardiepros.com
