Fasteners must be no closer than 25 mm (1 in) from ends of trim and spaced a maximum of 406 mm (16 in) O.C. Ensure trim is adequately fastened. James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together.
HardieTrim 5-4 Installation Inst_HZ5_1
Error message | View complete answer on https://www.jameshardiepros.com
Can you nail through Hardie board?
You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom. It’s best to use siding nails for face nailing or roofing nails for blind nailing.
Error message | View complete answer on https://legacyusa.com
What is the best way to nail Hardie board?
James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.
Error message | View complete answer on https://www.jameshardie.com
Are there special nails for Hardie board?
TIP: Stainless steel fasteners are recommended when installing James Hardie products. Corrosion-resistant siding nails 11/4 in. long should be used to apply individual HardieShingles® to minimum 7/16 in.
Error message | View complete answer on https://www.jameshardiepros.com
What size finish nails for Hardie trim?
Use a 50mm (2″) finish nail to fasten trim together. Longer finish nails may bend. INSTALLATION INSTRUCTIONS MAY LEAD TO SERIOUS PERSONAL INJURY OR DEATH. HardieTrim board is a decorative non-load bearing trim product.
Error message | View complete answer on https://www.jameshardiepros.com
Can you put a nail into Hardie board?
For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency. At the bottom, the siding should be face nailed, and at the top, it should be blind nailed.
Error message | View complete answer on https://legacyusa.com
Can you nail or screw into Hardie board?
Use screws or nails explicitly designed for attaching to Hardie boards. Regular nails and screws will not penetrate the surface properly and can cause damage. Be careful not to overdrive the nails – Ensure you drive the pins firmly and don’t overdo it.
Error message | View complete answer on https://gsexteriorexperts.com
Can you hammer a nail through Hardie board?
Yes you can. We recommend using 1 1/4″ smooth shank nails that are designed for use with Hardie Siding and Hardie Plank Siding.
Error message | View complete answer on https://www.quora.com
Can you nail into Hardiplank siding?
James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.
Error message | View complete answer on https://www.jameshardie.com
What are the best nails to use with Hardie board?
TIP: Stainless steel fasteners are recommended when installing James Hardie products. Corrosion-resistant siding nails 11/4 in. long should be used to apply individual HardieShingles® to minimum 7/16 in.
Error message | View complete answer on https://www.jameshardiepros.com
Is it better to nail or screw Hardie board?
James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above.
Error message | View complete answer on https://www.jameshardie.com
What kind of nails to use on cement board?
For thick or heavy metal fixtures, you’ll need 1 ⅝‑inch concrete board screws. If you’re using galvanized nails, a general 1 ½‑inch galvanized nail should hold the concrete board firmly in place. Make sure the screw head is slightly indented into the cement board.
Error message | View complete answer on https://www.fastenmaster.com
Does Hardie board require special nails?
TIP: Stainless steel fasteners are recommended when installing James Hardie products. Corrosion-resistant siding nails 11/4 in. long should be used to apply individual HardieShingles® to minimum 7/16 in. OSB rated sheathing.
Error message | View complete answer on https://www.jameshardiepros.com
What kind of nails to use for Hardie panels?
James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates.
Error message | View complete answer on https://www.jameshardiepros.com
Can you put a nail in Hardie board?
For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency. At the bottom, the siding should be face nailed, and at the top, it should be blind nailed.
Error message | View complete answer on https://legacyusa.com
What fasteners to use with Hardie board?
James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates.
Error message | View complete answer on
Can I use a finish nailer for Hardie siding?
The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. While it’s recommended to always use a siding nail gun for siding installation, in a pinch, you may be able to use a framing nailer instead.
Error message | View complete answer on https://www.nailgundepot.com
What size nail gun for Hardie siding?
Coil Nailer Siding / Fence Hardie Board Nail Gun 2 1/2″ Inch 15 Degree (RECON)
Error message | View complete answer on https://www.amazon.com